ASROCK G41M-PS ATHEROS LAN DRIVER DETAILS:
|File Size:||18.8 MB|
|Supported systems:||Windows 10, Windows 8.1, Windows 8, Windows 7, Windows 2008, Windows Vista|
|Price:||Free* (*Free Registration Required)|
ASROCK G41M-PS ATHEROS LAN DRIVER
MB ASRock G41M-VS3 R2.0, s775/G41,VGA,LAN,PCIe x16,PCI,ATA100,4xSATAII,2xDDR3/1333,ATX
Please follow below instructions according to the OS you install. Before Asrock G41M-PS Atheros LAN install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so may cause physical injuries to you and damages to motherboard components. Do not over-tighten the screws! Doing so may damage the motherboard.
Unplug the power cord from the wall socket before touching any component. To avoid damaging the motherboard components due to static electricity, NEVER place your motherboard directly on the Asrock G41M-PS Atheros LAN or the like. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components.
Hold components by the edges and do not touch the ICs. Whenever you uninstall any component, place it on a grounded antistatic pad or in Asrock G41M-PS Atheros LAN bag that comes with the component. Before you Asrock G41M-PS Atheros LAN or remove any component, ensure that the power is switched off or the power cord is detached from the power supply. Do not force to insert the CPU into the socket if above situation is found. Otherwise, the CPU will be seriously damaged.
ASRock > G41M-PS
Rotate the load lever to fully open position at approximately degrees. Rotate the load plate to fully open position at approximately degrees. Hold the CPU by the edges where are marked with black lines. Locate Pin1 and the two orientation key notches. Carefully place the CPU into the socket by using a purely vertical motion. Verify that the CPU is within the socket and properly mated to the orient keys. Use your left hand index finger and thumb to support the load plate edge, engage PnP cap with right hand thumb and peel the cap from the socket while pressing on center of PnP cap to Asrock G41M-PS Atheros LAN in removal.
It is recommended to use the cap tab to handle and avoid kicking off the PnP cap. This cap must be placed if returning the motherboard for after service. Rotate the load plate onto the IHS.
While pressing down lightly on load plate, engage the load lever. Secure load lever with load plate tab under retention tab of load lever.
|ASRock K7Upgrade-880 VIA 4 in 1||Bestil inden kl. 14.00|
|AMD FirePro Unified||System Requirements|
|Asus P8Z77-V LE||Kundeservice|
|ASUS BM6660 Intel LAN||Added to Cart|
|ATI RICHLAND 9995||Popular ASRock Motherboards drivers:|
Before you installed the heatsink, you need to spray thermal interface material between the CPU and the heatsink to improve heat dissipation. Ensure that the CPU and the heatsink are securely fastened and in good contact with each other. For proper installation, please kindly refer to the instruction manuals of your CPU fan and heatsink.
- ASROCK G41M-VS3 R - Motherboard
- [SOLVED] Ethernet Port not detected after Mother Board Replacement
- ASROCK G41M-VS3 R (DDR3)
- ASRock G41M-VS3 - 2.0 - motherboard - micro ATX - LGA775 Socket - G41
- Mother G41M-S3 - Asrock - Unboxing by www.geekshive.com
- ASRock G41M-VS3 Micro-ATX LGA775 Intel G41 Express
Apply thermal interface material onto center of IHS on the socket surface. Place the heatsink onto the socket.
Align fasteners with the motherboard throughholes. Rotate the fastener clockwise, then press down on fastener caps with thumb to install and lock. Repeat with remaining Asrock G41M-PS Atheros LAN. If you press down the fasteners without rotating them Asrock G41M-PS Atheros LAN, the heatsink cannot be secured on the motherboard. Connect fan header with the CPU fan connector on the motherboard. Secure excess cable with tie-wrap to ensure cable does not interfere with fan operation or contact other components.
Otherwise, it will operate at single channel mode. If you install only one memory module or two non-identical memory modules, it is unable to activate the Dual Channel Memory Technology. Unlock a DIMM slot by pressing the retaining clips outward. Installing an expansion card Step 1. Before installing the expansion card, please make sure that the power supply is Asrock G41M-PS Atheros LAN off or the power cord is unplugged.
Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation. Registration is quick, simple and absolutely free. Join our community today!
Note that registered members see fewer ads, and ContentLink is completely disabled once you log in. Are you new to LinuxQuestions. There is a chance that other OSes could also be suitable, Asrock G41M-PS Atheros LAN it is not advisable that you install this release on platforms other than the specified ones. Remember to perform a system reboot once done, to allow all changes to take effect properly. Asrock G41M-PS Atheros LAN Driver DOWNLOAD NOW.
1, downloads · Added on: Sep 28th, · Manufacturer: Asrock G41M-PS Atheros LAN. G41M-PS. Solid Capacitor for CPU Power; Supports FSB/// MHz CPUs RAM, XFast LAN, XFast USB Technologies; Supports Instant Boot, Instant Flash, LAN. - PCIE x1 Gigabit LAN 10// Mb/s - Atheros® AR